Find or Sell any Parts for Your Vehicle in USA

2awg Bmw E28 E30 E31 E34 Engine To Chassis Upgrade Ground Cable. #2gnd16 on 2040-parts.com

US $28.00
Location:

Martinez, California, US

Martinez, California, US
Returns Accepted:ReturnsNotAccepted Part Brand:Royal Excelene

Is your Engine Ground cable looking greasy, old, corroded, or deteriorated? Did you know the Engine Ground Cable completes the current flow for most of the engine related electronics?  Did you know a poor engine ground on your BMW can cause problems with fluctuating/inaccurate temperature gauge, occasional no crank from starter, dimming parking/headlights, among many other electrical related problems?


These Engine to Chassis ground cables are hand made by a professional Electrical Technician with over 10 years professional experience using professional tools and techniques.  I'll explain and prove...see pictures below. 

Each purchase is for a single 16 inch (hole to hole) cable assembly.  It is slightly longer than OEM to make for easier installation. 

This cable set will fit BMW's with the following engines: 
E30: M42
E34: M20, M30, M50, M60
E28: M21
E32: M30, M60, M70
E31: M60, M62, M70, M73, S70

Here are the specs of the cable and components are used. Made in USA.

Cable Conductor - #2AWG 99.999% purified electrolytic copper
Cable Insulation - CCI Royal Excelene (resists oil, burning, abrasion, cold weather and is rated at 600 volts/3 hours, -58F to 221F) 
Lugs - 3/8in dia through hole, copper 
Heat shrink - Irradiated Polyolefin (flame retardant, -47F to 257F) 
Additional specs - Highly flexible welding cable, which in my professional opinion, is the best power cable because its resistant to multiple climates, temperatures, oils, gas, and can withstand extreme amounts of current. Also highly conductive copper. These cables will last several decades! 

Because this cable is almost twice as thick as the OEM cable, it will handle much more current for faster starter crank times and to supply power to your upgraded electronics.

Insulation is stripped, using professional techniques that avoids ANY possible nicks or scores.  Wire that is stripped in a un-professional manner will have nicks and scores that will break over time and/or during the moment of crimping. This will lead to failure of the termination. 
 
First crimped using Klein crimpers under high pressure. Each end is soldered using 60/40 tin/lead and a torch.  Note the complete absorbing of solder.         
Polyolefin heat-shrink tubing applied
    
Each termination is cleaned for maximum conductivity.
   
Completed Engine to Ground Cable 2AWG 
 photo IMG_2286.jpg

Toyota Prius wagon is roomier, heavier than its hatchback sibling

Tue, 08 Mar 2011

The new wagon-style Toyota Prius has entered production ahead of its global sales debut next month in Japan. And despite outward similarities with its hatchback predecessor, the newest member of the Prius family also gets noteworthy changes. At a preview and test drive for journalists in Japan, Toyota Motor Corp.

Mercedes CLA starts to roll off production line in Hungary

Fri, 25 Jan 2013

The Mercedes CLA – the baby Mercedes CLS based on the new A Class – has started to roll off the production line at Kecskemét in Hungary. But that’s probably unfair; based as it is on the new A-Class, the CLA is a very good car under the skin, even if its big USP is the dramatic styling. Now, just over a week after the CLA got its first public reveal (if you don’t count the Mercedes Concept Style Coupe on which its based), the first production car has rolled off the line at the Mercedes plant in Kecskemét, Hungary.

NASCAR's sexy French past

Tue, 05 Feb 2013

In the post-Jean Girard era, your stereotypical NASCAR fan probably doesn't spend too much time thinking about France. Unless it's Bill France Sr., Bill France Jr., or Jim France, or Brian France, or Amy France. Ok, so NASCAR fans might actually think about Frances fairly often, but probably not the French Republic.