Vinyl Film Tint 12" X 24" Headlight Taillight Fog Wrap Cover Gloss Golden on 2040-parts.com
广东, China
|
Description Features: 1 piece of Brand New, self-adhesive 12'' x 24"=（30x60cm） Self-Adhesive Selective Charming light smoke Vinyl Film Tint Wrap For Car Headlights Fog Lights Lamps. This is the high quality yellow protection vinyl film sheet that you've been waiting for so long in glossy finishing for varieties of places such as headlights, tail lights, fog lights, side marker lights, bumpers, hood or even windshield. Fitment: Universal fit, even though the parts compatibility list only shows 300 vehicles, but this product will fit any cars, SUVs or trucks. You can use this vinyl film for any headlights, fog lights, sidemarker lights or even top part of the windshield, etc. Simply clean the surface and apply this high quality vinyl sheet to anything smooth surface and cut off the edge. It will not damage your lamp nor leave any residual These kits are universal they fit all makes and models. They are NOT Pre-Cut and are much easier to install then Pre-cuts. This kit is for 1 sheet 30" x 50". Additional kits may be required for complete coverage of two or more lights. Package: 1* 12'' x 24" Gloss Light Smoke Headlight Cover Sticker 2, easy installation, good viscosity, does not affect the original light source, waterproof sunscreen. 3, with a strong protective effect, scratch-resistant, durable. 4, the product environmental protection, not on the human body and the environment to produce toxic side effects and pollution. 5, suitable for DIY operation. Sticker paste operation instructions: Dry paste method】 【motorcycle stickers or small stickers apply 【Dry sticking method steps】 Use tools: clean rags, scraping, credit cards 1, clean the body paste position, conditions can be used without fiber off the cloth dipped in 50% of the Alcohol or isopropyl alcohol or acetone to scrub, but also with soapy water; the surface of the solvent to be cleaned After the solvent is completely evaporated, paste 2, the transfer film (paste in the reflective paste on the transparent film) together with the car stickers lifted; Case, the slow side of the paste, while scraped with a tool, while the end of paper to expose. 3, if the car sticker length and width are less than 10 cm, you can peel all the stickers and then paste. But must be careful , Do not accidentally stick or fall off the ground sticky dust. 4, with a clean rag or scraping [such as phone cards or credit cards] on the transfer film repeatedly wiping or scraping scraping A few; until there is no bubble inside the car stickers, and then torn [transparent] transfer film can be recommended 24 hours Do not exposure or car wash. 【Wet stickers】 car stickers or large car stickers apply [Recommended double operation] 【Wet sticker steps】 Use tools: watering can, clean rags, scraper, utility knives, hairdryer 1, will need to paste the surface clean in preparation for the paste before the glass water evenly spray on the need to paste Surface (after cleaning the car body, will be posted on the body parts with watering can) - mainly used to Reduce sticker viscosity, easy to adjust the position. 2, to determine the need to paste the location of the post, together with the car stickers from right to left to [or from top to bottom] lift a Side and with a cloth to its pressure on the car table, and then while the paste, while flattened with a rag, while exposing Bottom paper. 3, encountered a door handle or anti-collision of the material according to the circumstances cut open and included or loaded. 4, timely adjustment, the general location of the figure to determine correct, scraper with the scraper repeatedly water and air bubbles, When using the scraper from right to left oblique scraping. 5, case of the door and sewing with a utility knife are divided open, inward package affixed. 6, as far as possible in the car stickers in the water dry, conditional heating tube can be properly dried. Suggest: 24 hours as far as possible not exposure, 48 hours should not be washed.   |
Headlight & Tail Light Covers for Sale
Vinyl film tint 12" x 24" headlight taillight fog wrap cover gloss purple
Ford mustang tail light covers - fits 1993 mustang **look**(US $50.00)
Trailer hitch wiring tow harness for subaru forester 2009 2010 2011 2012 2013(US $35.00)
Draw-tite trailer hitch wiring tow harness for nissan nv200 2013 2014(US $56.00)
Chrome side door handle bowl cover cup trim for honda vezel hr-v 2014 2015(US $18.55)
B623-51-283 brand new genuine mazda oem license lamp cover rh (cover bombilla)(US $32.25)
X-Wave concept from Visteon/3M (2008): first pictures
Mon, 02 Jun 2008By Adam Towler First Official Pictures 02 June 2008 09:36 Want to see the future of the car cockpit? The X-Wave concept is a showcase for the latest thinking on vehicle interiors from automotive supplier Visteon and technology giant 3M. They’ve teamed up to fit out a BMW X5 – dubbed X-Wave – with new lighting and control interfaces that could revolutionise the look and operation of cars over the next few years.
Jaguar Land Rover leads UK universities to develop virtual simulation tech
Tue, 11 Jun 2013Jaguar Land Rover is to lead four UK universities in a £10m ($15.5m) government scheme to develop virtual simulation technologies and processes to help improve and accelerate the car design process. The carmaker will be leading project teams from the universities of Cambridge, Loughborough, Leeds and Warwick in the Program for Simulation Innovation (PSI), developed to improve the potential of the UK virtual simulation industry. It is hoped that through its results design quality and capability can be improved through the simulation of sights, sounds and smells.
Ford Focus RS will hit 164mph
Thu, 27 Nov 2008The 2009 Ford Focus RS - Good for 164mph [ad#ad-1] Ford in Austria has finally let loose some concrete information on the much anticipated 2009 Ford Focus RS, which looks set to be one barn-stormer of a car. With almost 300bhp, a 0-60 time in the high 5 seconds and a top speed of 164mph, the Focus RS looks an enticing package for the boy racers. Austrian prices are quoted at €39,000, which at today’s rotten rates equates to about £32.5k.